Server Products - Quick Start Guide SR1625UR

May 11, 2023 – 03:09 am

The quick start user's guide for the Intel ® Server System SR1625UR provides instructions on how to integrate the processor, memory and supported accessories. This is an HTML version of the guide is available for download a PDF version.

Begin by reading the safety information for the Intel system. Observe normal ESD precautions when installing add-in cards.

You must use tested processors , memory and hardware during the integration and operation to avoid problems that may occur.

Step 1-4: prepare your system by removing the cover, risers, air baffle and heat sink.
Step 5-6: Install the processor and the heat sink
Step 7: Install memory
Step 8-9: Installing optional components, module i / o Intel ® RMM3
Step 10: Installing the active system (product code: SR1625URSAS) components
Step 11: Install a passive system (product code: SR1625UR) components
Step 12: The installation of hard drives
Step 13: The installation of optical devices (optional)
Step 14: Install second power supply
Step 15: Installing a control panel
Step 16: The installation of the air duct
17-18 Step: Install Add-In Card (optional)
Step 19-22: finish

Step 1: Place the Intel server system on a flat antistatic to perform the procedures of previous integration.

Step 2: Remove the cover from the chassis by performing the following actions.
(A) remove the security screw.
(B) press the latch.
(C) Slide cover back and lift up.

Step 3: Remove Add-in riser card assembly holding the riser assembly with both hands and pulling it upwards.

Step 4: Remove the processor air duct, sink and spacer before installing the processor.

Step 5: Install the processor following the procedure described below. This page contains a list of processors tested .

Step 6: Install the heat sink, start with screw # 1 as shown on the moving sequentially, do not overtighten the screws.

Step 7: Install memory DIMMs. This page contains a list of tested memory . For optimal performance, we recommend a minimum of three DIMMs per CPU.

Step 8: Install the expansion module I / O (optional).

(A) squeeze the sides of the filler panel to remove the rear panel of the chassis. If you are using a socket 2 expansion module i / o, remove the filler panel according to following the procedure indicated above. If you use only one plug 1 IO expansion module current, do not remove the second blank.

(B) install the spacers as shown below.


Big (HUGE) question marks

2006-01-19 13:53:45 by NoeNick

You do know this product isn't granite? I'm very suspicious of the 'polymer' compound countertops in terms of use, scratching, heat, etc. They always tell people that surfaces like Corian can be sanded out if you get a burn or bad scratch but they fail to remind you about the Grand Canyon that results when you sand Corian deep enough to remove a burn.
Then ... how thick is it? How much are your adding to the height of your countertops? You'd be surprised the difference an inch can make, especially if you're not 6' tall.
And ... how do they accomodate the sink and wet areas? I'd be very suspicious about mounting an undercounter sink on top of old countertops and then putting a new top over the whole thing

You might also like:

Newegg TV: Arctic Silver CPU Heatsink/Fan Replacement Guide
Newegg TV: Arctic Silver CPU Heatsink/Fan Replacement Guide

SilverStone Tundra TD02 & TD03 CPU Liquid Coolers Review  — Hard OCP
We are very excited for these updates and can't wait to put our new coolers to the test. Speaking of cooler .. The thermal paste has been shown to provide excellent thermal conductivity allowing the heat sinks to better do the job.

ASRock Z87M OC Formula Review: mATX OC at $190  — AnandTech
ASRock also likes to promote their use of an 8-layer PCB with micro-ATX, and inclusion of a higher quality thermal paste (GELID GC-Extreme) with the package to help users with their overclocks.

Related posts:

  1. Copper heat sink computer
  2. Use of heat sink in Computers
  3. Computer heat Sink compound
  4. Heat Sink Compound Paste
  5. LED LAMP heat sink design